“数字信号处理”课程的几何视角

“数字信号处理”的经典课程体系以“系统”为中心，以离散时间傅立叶变换、z变换和离散傅立叶变换为分析工具，以滤波器设计为目的，注重定理和公式推导及其性质分析，很难让学生建立一个形象的、完整统一的知识体系框架。本文从几何视角将 “系统”化和“代数”化的经典课程体系重构为面向“信号”的“几何”知识体系，从而提升学生对本质问题的“洞察力”，帮助学生建立系统的知识体系。     

“数字电子技术”课程思政教学改革研究

落实立德树人,实现三全育人,将思政融入到《数字电子技术》这门专业课程中,培养学生专业知识的同时,引导学生树立良好的人生观和价值观。通过重构本校的数字电子技术课程内容,挖掘思政元素,并润物细无声般融入到数字电子技术的教学改革中,并通过实际的案例讲解具体融入过程。     

传统企业数字化转型能力体系构建研究

企业试图完成数字化转型,这是在竞争中谋求发展的必经之路。文章率先进行数字化转型特征、策略的概念分析,而后总结以此为背景的能力模型、企业管理能力与技术能力,最终以某公司案例完成体系构建与应用的阐述。     

用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。     

Synergistic effect of Fe and Ag co-doping on the persistent photoconductivity of vertical ZnO nanorods

Undoped, doped and co-doped vertically aligned ZnO nanorods (NRs) are synthesized using sonicated sol-gel immersion method. A significant variation in structural, morphological, optical and photoconductivity properties of ZnO NRs after incorporation of transition metal ions (Fe or/and Ag) is obtained. XRD analysis revealed that incorporation of Fe ameliorates while that of Ag deteriorates the c-axis growth of NRs. The diameter of the NRs is tuned from 236 nm to 103 nm. The Fe-doped ZnO NRs exhibit significantly thinner diameter, longer length, and highest aspect ratio. The doping and co-doping reduces the optical band gap of ZnO by 20 meV and 10 meV respectively. A reduction in near band edge emission whereas enhancement in defect-related-green-emission is obtained. Noticeable enhancement in the light harvesting efficiency and significant quenching of the persistent photoconductivity is obtained by co-doping.     

Phase constitution,microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

In this study, a kind of Ni-based superalloy specially designed for additive manufacturing (AM) was investigated. Thermo-Calc simulation and differential scanning calorimetry (DSC) analysis were used to determine phases and their transformation temperature. Experimental specimens were prepared by laser metal deposition (LMD) and traditional casting method. Microstructure, phase constitution and mechanical properties of the alloy were characterized by scanning electron microscopy (SEM), transmission scanning electron microscopy (TEM), X-ray diffraction (XRD) and tensile tests. The results show that this alloy contains two basic phases, γ/γ', in addition to these phases, at least two secondary phases may be present, such as MC carbides and Laves phases. Furthermore, the as-deposited alloy has finer dendrite, its mean primary dendrite arm space (PDAS) is about 30-45 μm, and the average size of γ' particles is 100-150 nm. However, the dendrite size of the as-cast alloy is much larger and its PDAS is 300-500 μm with secondary and even third dendrite arms. Correspondingly, the alloy displays different tensile behavior with different processing methods, and the as-deposited specimen shows better ultimate tensile stress (1,085.7±51.7 MPa), yield stress (697±19.5 MPa) and elongation (25.8%±2.2%) than that of the as-cast specimen. The differences in mechanical properties of the alloy are due to the different morphology and size of dendrites, γ', and Laves phase, and the segregation of elements, etc. Such important information would be helpful for alloy application as well as new alloy development.